Vels Arena of Cricket: 03/23/12

COPYRIGHT OWNED BY MARYLBONE CRICKET CLUB

LAW 7 THE PITCH
1. Area of pitch
The pitch is a rectangular area of the ground 22 yards/20.12m in length and 10 ft/3.05m in
width. It is bounded at either end by the bowling creases and on either side by imaginary
lines, one each side of the imaginary line joining the centres of the two middle stumps, each
parallel to it and 5ft/1.52m from it. See Laws 8.1 (Width and pitching) and 9.2 (The bowling
crease).
2. Fitness of pitch for play
The umpires shall be the sole judges of the fitness of the pitch for play. See Laws 3.8
(Fitness for play) and 3.9 (Suspension of play in dangerous or unreasonable conditions)
3. Selection and preparation
Before the match, the Ground Authority shall be responsible for the selection and preparation
of the pitch. During the match, the umpires shall control its use and maintenance.
4. Changing the pitch
The pitch shall not be changed during the match unless the umpires decide that it is
dangerous or unreasonable for play to continue on it and then only with the consent of both
captains.
5. Non-turf pitches
In the event of a non-turf pitch being used, the artificial surface shall conform to the
following measurements.
Length - a minimum of 58 ft/17.68m
Width - a minimum of 6 ft/1.83m
See Law 10.8 (Non-turf pitches)

[Meaning for some important terms in TAMIL:consent-சம்மதம்,turf-புல் தரை]

Posted by:Vels Arena of Cricket / velsaoc.blogspot.com

COPYRIGHT OWNED BY MARYLBONE CRICKET CLUB

LAW 6 THE BAT
1. The bat
The bat consists of two parts, a handle and a blade.
2. Measurements
All provisions in sections 3 to 6 below are subject to the measurements and restrictions
stated in Appendix E.
3. The handle
(a) One end of the handle is inserted into a recess in the blade as a means of joining the
handle and the blade. The part of the handle that is then wholly outside the blade is
defined to be the upper portion of the handle. It is a straight shaft for holding the bat.
The reminder of the handle is its lower portion used purely for joining the blade and the
handle together. It is not part of the blade but, solely in interpreting 5 and 6 below,
references to the blade shall be considered to extend also to the lower portion of the
handle where relevant.
(b) The handle is to be made principally of cane and/or wood, glued where necessary and
bound with twine along the upper portion.
(c) Providing 7 below is not contravened, the upper portion may be covered with materials
solely to provide a surface suitable for gripping. Such covering is an addition and is not
part of the bat. Note, however, 8 below.
(d) Notwithstanding 4 (c) and 5 below, both the twine binding and the covering grip may
extend beyond the junction of the upper and lower portions, to cover part of the
shoulders as defined in Appendix E.
4. The blade
(a) The blade comprises the whole of the bat apart from the handle as defined above.The
blade has a face, a back, a toe, sides and shoulders. See Appendix E.
(b) The blade shall consist solely of wood.
(c) No material may be placed on or inserted into either the blade or the lower portion of
the handle other than as permitted in 3 (d) above and 5 and 6 below, together with the
minimal adhesives or adhesive tape used solely for fixing these items, or for fixing the
handle to the blade.
5. Covering the blade
All bats may have commercial identifications on the blade. Type A and Type B bats may
have no other covering on the blade except as permitted in 6 below. Type C bats may
have a cloth covering on the blade. This may be treated as specified in 6 below.
Such covering is additional to the blade and is not part of the bat.Note ,however,8 below.
6. Protection and repair
Providing neither 4 above nor 7 below is contravened,
(a) solely for the purposes of
either (i) protection from surface damage to the face,sides and shoulders of the blade
or (ii) repair to the blade after damage
material that is not rigid, either at the time of its application to the blade or
subsequently, may be placed on these surfaces. Any such material shall not extend
over any part of the back of the blade except in the case of (ii) above and then only
when it is applied as a continuous wrapping covering the damaged area.
(b) solid material may be inserted into the blade for repair after damage other than surface
damage. Additionally, for protection from damage, for Types B and C, material may be
inserted at the toe and/or along the sides, parallel to the face of the blade.
The only material permitted for any insertion is wood with minimal essential adhesives.
(c) to prevent damage to the toe, material may be placed on that part of the blade but shall
not extend over any part of the face, back or sides of the blade.
(d) the surface of the blade may be treated with non-solid materials to improve resistance to
moisture penetration and/or mask natural blemishes in the appearance of the wood. Save
for the purpose of giving a homogeneous appearance by masking natural blemishes, such
treatment must not materially alter the colour of the blade.
Any materials referred to in (a), (b), (c) or (d) above are additional to the blade and not
part of the bat. Note, however, 8 below.
7. Damage to the ball
(a) For any part of the bat, covered or uncovered, the hardness of the constituent materials
and the surface texture thereof shall not be such that either or both could cause
unacceptable damage to the ball.
(b) Any material placed on any part of the bat, for whatever purpose, shall similarly not be
such that it could cause unacceptable damage to the ball.
(c) For the purposes of this Law, unacceptable damage is deterioration greater than normal
wear and tear caused by the ball striking the uncovered wooden surface of the blade.
8. Contact with the ball
In these Laws,
(a) reference to the bat shall imply that the bat is held in the batsman's hand or a glove worn
on his hand, unless stated otherwise.
(b) contact between the ball and
either (i) the bat itself
or (ii) the batsman's hand holding the bat
or (iii) any part of a glove worn on the batsman's hand holding the bat
or (iv) any additional materials permitted under 3, 5 or 6 above
shall be regarded as the ball striking or touching the bat or being struck by the bat.

[Meaning for some important terms in TAMIL: recess-ஒதுக்கிடம், cane-பிரம்பு, glue-பசை, contravene-மீறுதல், rigid- கடினமான, wrapping-உறையிடும், blemishes-கறைகள், homogeneous-ஒரே மாதிரி, ஒரே இயல்பான,deterioration-தரம் கெடுத்தல்]

Posted by:Vels Arena of Cricket / velsaoc.blogspot.com